مشاهده
Installing a Vimpex Loop Sounder System with short-circuit isolation provides complete sounder circuit integrity. By wiring the sounder circuit in a loop instead of a traditional radial, all sounders will remain operational in the event of a short-circuit or open circuit fault.
Stratos-Micra 100 has two pipe inlets and supports a maximum of 100 metres of sampling pipe.Stratos-Micra is available with an optional ‘Piped Exhaust’ type Docking Station. This is primarily intended to allow the Stratos-Micra detector to sample from areas which may be at different air pressure to the detector location. Typical uses are for air-duct sampling and allowing the installation of the detector in under-floor or ceiling voids or when sampling from pieces of computer related equipment.
The bell remains the most commonly used alarm for fire evacuation systems. Recognising this, Vimpex continue to innovate with their all-aluminium range of fire alarm bells. Five bells make up the range of 150mm (6 inch) and 200mm (8 inch) internal and external units. Being of aluminium construction, our bells have a very high volume output matched with extremely low power consumption - just 11mA for the 150mm internal.
Using the market leading aluminium gong for excellent sound output and a clear lens to maximise light output, the Vimpex StroBell is ideal for installations that call for a traditional bell tone but require visual indication as well.As with the Vimpex sounder range, all bells can be supplied branded with your company logo.
The Mini Stopper consists of a clear tough polycarbonate hinged cover that retrofits securely over the device. Simply lift the cover to gain access to the device. Once the cover is released the spring loaded hinge returns the cover to its original position.
Vimpex has incorporated a number of innovative lens and LED light technologies into the VAD23 Range that maximises light output for minimum current. With models that combine both a traditional electronic sounder or a voice sounder with a low current EN 54-23 rated VAD, the VAD23 is truly the most versatile family of visual alarm devices currently available - providing flexible solutions for the designer and end-user.
The IS FlashDome is an intrinsically safe strobe for use in hazardous areas. Certified to ATEX and IEC Ex, the IS FlashDome is designed for use in Zones 0, 1 & 2.
In order to be intrinsically safe, the IS FlashDome must be powered via an approved 28v 300Ohm zener barrier or galvanic isolator.
Suitable barriers and isolators are available from Vimpex.
The Ani-Mate® animal friendly sounder uses a specifically developed low frequency tone (sub 400 Hz) that is designed to minimise discomfort to animals. The Ani-Mate® is designed to conform to the ‘silent’ fire alarm. The ‘silent’ fire alarm(1) was developed because of the need for an effective alarm signal in laboratory animal facilities which did not stress the animals every time it was tested. Small mammals in particular can be distressed by the frequency of tones emitted by standard electronic sounders and bells. It is only by using a conventional cone loudspeaker that pure low frequencies can be reproduced and thus disturbance to animals be minimised.
This compact 105dBA Security Sounder is designed as a stand alone unit for internal use. The unit is also capable of operating in an external protected environment such as polycarbonate bell boxes. The unit is surface mounted and is able to utilise square trunking.
The Vimpex EX Series of Explosion-Proof Sounders and Strobes are available in a number of different versions and configurations to meet the demanding requirements of alarm notification in hazardous areas. Models include sounders, strobes, combined sounder strobes, manual call points and switches. Typical applications include Oil and Gas, On-shore and Offshore, Petrochemical, Refineries and Marine.
DIN rail mounted galvanic isolators and zener barriers for use with both the IS28 sounder and the IS FlashDome beacon are available from Vimpex.
This product provides a secure method for safely isolating the mains voltage supply to fire systems in accordance with BS 5839: Part 1 : 2013.
LHD: Linear Heat Detection, as illustrated below, is easy to design, install, operate, and maintain. A typical system begins with any approved conventional or addressable fire alarm panel. A Distance Locating Module may be added to identify where the overheating condition is occurring. Leader wires are then run in conduit from either the panel, an addressable module, or the distance locating module, to the beginning of the zone.
Because they’re moulded of polycarbonate material in a highly durable design, these protective covers carry a lifetime guarantee against breakage in normal use. They are easy to remove for servicing and tamper-resistant hardware is available.
Stratos-Micra 25 is intended to provide LOCALISED incipient fire detection only. This means that it is suitable for the substantial range of applications typified by; small non-compartmentalised rooms, warehouse racking, or pieces of electronic or electromechanical equipment where it is desirable to achieve individual incipient fire reporting. In compartmentalised rooms, each compartment would normally use individual Stratos-Micra 25 detectors
Stratos-HSSD 2 embodies innovative features which depart from accepted techniques for detectors which operate at very high sensitivity. Perhaps the most important feature of the system is the adoption of a patented 'artificial intelligence' known as ClassiFire-3D. This controls all aspects of the system operation. ClassiFire-3D ensures that Stratos-HSSD 2 operates at maximum SAFE sensitivity to give warning of problems earlier than previously considered possible.
The Hydrosense Water Leakage Detection System is designed to protect areas where water ingress could seriously damage electrical, communication and computer networks. When installed in vulnerable areas it continuously monitors for water leaks.Hydrosense can be installed in a wide range of applications including HVAC, sprinkler systems and water-cooled plant
Signaline HD analogue heat sensing cable must be used with a Signaline HD controller and End of Line Unit. These enable the Signaline HD heat sensing cable to be fully monitored for open and short circuit. The controllers are equipped with volt free fire and fault relays that are connected to the fire control panel via an Interposing Line Unit. Alternatively the Controller can be used as a stand alone device using the relay contacts to activate subsidiary equipme
The ReSet Series 01 of EN54-11 approved resettable manual call points mimics the feel of breaking glass whilst offering the user the benefits and environmental advantages of a resettable operating element.Once installed, the ReSet need never be opened for test or reset. With no moving parts accessible to the engineer or user, the ReSet is proven to be highly reliable and robust.
The Call Point Stopper consists of a clear tough polycarbonate hinged cover that retrofits securely over the device. Simply lift the cover to gain access to the device. Once the cover is released the spring loaded hinge returns the cover to its original position.
The Alert Point is an aesthetically pleasing, robust and fully featured stand alone alarm system.
Powered with a 9v PP3 alkaline battery, the Alert Point includes an integral sounder and resettable call point.
Smart+Cage protects essential Fire, Safety and Security equipment from theft, vandalism or accidental damage. Constructed from PVC coated 4mm steel bar, these tough resilient waterproof cages provide security for a wide range of devices.
Here is an excellent way to protect your beacons and sounders against both vandalism and accidental damage. The newest members of the STI Wire Guard Team, these Stoppers were created in response to multiple requests from STI customers. They are easy to install with all screws and anchors provided.
This innovative wireless battery-powered magnetic Door Holder is triggered acoustically when the fire alarm sounders are activated. No external wiring is required and the unit is typically powered in excess of 12 months by 2 standard ‘C’ battery cells
Arguably the single most important fire safety mechanism, electromagnetic door holders guard against the lethal spread of toxic smoke and fumes - by far the greatest cause of death in fires.
The Zeta magnetic door holders are designed to retain a fire door open against the force of its own closing device. In the event of a fire, the door holder magnet can be turned off by the fire alarm, allowing the door to shut.
Arguably the single most important fire safety mechanism, electromagnetic door holders guard against the lethal spread of toxic smoke and fumes - by far the greatest cause of death in fires
The Vimpex Relay Interfaces are designed to provide a connection between external equipment and alarm systems. Building Management Systems (BMS), security, fire and smoke dampers and lift shutdown are just some of the applications for this device.
Distance Locating is available for SafeCable and allows you to locate where the fire or overheating condition is occurring anywhere along its entire length. The distance is displayed in both feet and meters.
The Identifire series of EN 54-4 Approved switched-mode power supplies has intelligent on-demand load sharing capability to provide exceptional flexibility. This allows rapid large capacity battery charging with either extended standby hold-up duration at light loads, or short high current peak loads where spare output capacity is diverted to battery charging.
The Vimpex VPSU 12 and VPSU 24 series of PSUs are switched mode power supplies ideal for general use, door holders and CCTV cameras.
Designed for fire detection systems requiring local indication of an individual or group of fire detectors in alarm mode, the VRLU indicator utilises an ultra-bright LED with a wide range of illumination.
These super tough wire guards are designed to protect clocks, bells and similar instruments. Three sizes are available to cover a wide range of units. Each is constructed of 9-gauge steel wire with corrosion resistant polyester coating. Their octagon, spiderweb like shape also helps them take tough knocks in stride.
The Smart+Guard is a tough polycarbonate hinged protective cover that can easily be installed over a range of call points, emergency switches and other devices to provide protection from vandalism, accidental damage or misuse.
Stop unauthorised exits and entries through emergency exit doors. The Exit Stopper is a unique and highly effective way to alert you to any unauthorised exits or entries through any emergency exit door. It can also serve as an inexpensive security device and help prevent theft.
Stop theft, vandalism or misuse of fire extinguishers. If you are fed up with replacing or recharging your fire extinguisher, this sturdy, tamper-proof, self-contained device is the answer. It has proven highly effective in helping stop theft, misuse or vandalism of fire extinguishers. The Extinguisher Stopper will leave the extinguisher totally accessible for emergencies and will not interfere in the event
سری متعارف
داراي تأييديه - CPR LPCB
سازگار با تمام سیستم های اعلام حریق متعارف